Blog

Fixing a Puncture on a Bike or E-Bike: From the Pro Approach to Emergency Survival

19.04.2026 • Admin • 5 min read
Fixing a Puncture on a Bike or E-Bike: From the Pro Approach to Emergency Survival

The sound of air hissing out of a tyre can ruin your mood instantly. On a conventional bike it's annoying, but on a 25-kilogram e-bike, where the rear wheel carries a cassette, a brake disc and often a speed sensor too, it can feel like a nightmare.

A puncture isn't the end of the world, though. Whether you're equipped like a mobile workshop or standing in the woods empty-handed, there is a way to get home.

Scenario 1: I have tools (the ideal approach)

If you have tyre levers, a spare tube (or patches) and a pump in your backpack, the repair is just a matter of practice. With e-bikes, though, you need to allow for the extra weight and stiffer (often reinforced) tyres.

E-bike specifics (rear wheel):
Shift into the hardest gear (the smallest rear sprocket) so the chain is easier to handle. If your derailleur has a clutch (a lever on the derailleur that stops the chain bouncing), switch it off before removing the wheel. If you have an e-bike with a rear hub motor, remember to disconnect the motor power cable before loosening the axle.

The right way to change a tube:

  • Removing the tyre: Slide a tyre lever under the tyre bead, lever it over the rim and hook it onto a spoke. Run a second lever around the rim until one side of the tyre is off.
  • Finding the culprit (a critical step): Before fitting the new tube you absolutely must run your fingers around the inside of the tyre. If a thorn or a bit of wire is still stuck in it, you'll puncture the new tube as soon as you inflate it.
  • Fitting the new tube: Put a little air into the new tube (so it takes a round shape and doesn't kink). Put the valve through the hole in the rim and push the tube evenly under the tyre.
  • Refitting the tyre: Using your hands (working outwards from the valve), push the tyre bead back onto the rim. The last 20 centimetres are usually the hardest – use a tyre lever here again.
  • Check and inflate: Check that the tube isn't poking out from under the tyre anywhere (otherwise it will burst like a balloon when you inflate it). Inflate to the required pressure.

Scenario 2: I have no tools (MacGyver in the wild)

Left your backpack at home and the wheel is flat? Before you start desperately pushing the bike, try these "survival" techniques. It will hurt (especially your fingers), but it can be done.

How to remove a tyre without tyre levers?
Use physics and the anatomy of the wheel. The rim is deeper in the middle than at the edges. Let every last bit of air out of the wheel. All the way round the wheel, squeeze the tyre hard so that both beads are pushed into the central (deepest) channel of the rim. This gives the tyre a bit of slack, and at one point you'll manage to pull it over the edge with the strength of your fingers (or with the help of a quick-release lever or a flat stone).

How to fix a hole without patches or a new tube?

  1. A knot in the tube: If you find where it was punctured, cut the tube at that point (if you have something to cut with, such as keys) or simply tie a tight knot at the site of the puncture. The tube will be a little shorter, but you'll be able to squeeze it back into the wheel. The bike will bump noticeably as you ride, but you'll protect the rim from being destroyed and get home.
  2. A grass-filled tyre (extreme rescue): If the tube is completely torn, take it out. Stuff as much grass, moss, leaves or pine needles as possible inside the tyre (really pack it tight). Put the tyre back on. It won't be comfortable, but the soft filling will keep the tyre on the rim and you can pedal slowly in an emergency.

Scenario 3: puncture repair spray (the quick and dirty alternative)

A repair spray (e.g. Pit Stop spray) contains compressed gas and a sealant (latex foam). For e-bikers who dread handling a heavy rear wheel, it's a huge relief, because you don't have to take the wheel out of the frame at all.

How it works:

  • Method: Remove the object that caused the puncture (if you can see it). Shake the can, screw on or firmly press the spray's hose onto the valve and press. Within a few seconds the spray inflates the wheel and injects foam inside. You then need to spin the wheel immediately (or start riding) so that centrifugal force spreads the sealant all around the inside and seals the hole.
  • Advantages: Extreme speed. The repair literally takes 60 seconds without getting your hands dirty from the chain.
  • Disadvantages: It's a lottery. The spray only seals small holes from thorns or small nails (up to 1–2 mm). If you have a sidewall puncture, a tyre slashed by glass or a so-called "snakebite" (the tube pinched against the rim when hitting an edge), the spray will blow out and just make a huge mess. It's also only a temporary solution – at home you'll have to replace the tube anyway and clean the sticky foam out of the tyre.